Pro Comp Jeep TJ / LJ Suspension Lifts

Features:

• Shocks: Front/Rear ES3000
• Max Tire Size: 31x10.50R15-20, 265/70R16, 255/70R17, 285/55R18, 275/55R20
• Wheel Size: 15" thru 20" up to 9" wide rims with 3.5" to 4.5" BS
• Front Lift: Coil Springs
• Rear Lift: Spacers
• Install Time: 2-4 Hours

Notes:

• (2) Driveline modifications may be required for height increases over 1.5" due to increased driveline angles. Transfer case SYE (Slip Yoke Eliminator) kit and CV rear drive shaft required for Long Arm Applications. Rubicon models will require CV drive shaft w flange adapter (not avail from Pro Comp).
• (3) Vehicles with Auto Trans will require removal of front skid plate when using transfer case lowering hardware.
• (4) All ride height increases are approximate and will vary due to vehicle specification (Engine size, factory options, trail equipment, etc).
• (5) Coil spacer 55496 can be used to increase front ride height by .75".
• (7) Vehicle will require alignment after kit is installed.
• (8) Front cambolt kit 20-65226 is recommended for caster angle adjustments. In most cases, reducing positive caster to the minimum factory specification will reduce or eliminate the potential for steering wheel shimmy.
• (9) Rear cambolt kit 20-65225 can be used for tuning pinion angle for minor driveline vibration correction.

Features:

• Shocks: Front/Rear ES3000
• Max Tire Size: 31x10.50R15-20, 265/70R16, 255/70R17, 285/55R18, 275/55R20
• Wheel Size: 15" thru 20" up to 9" wide rims with 3.5" to 4.5" BS
• Front Lift: Coil Springs
• Rear Lift: Spacers
• Install Time: 2-4 Hours

Notes:

• (2) Driveline modifications may be required for height increases over 1.5" due to increased driveline angles. Transfer case SYE (Slip Yoke Eliminator) kit and CV rear drive shaft required for Long Arm Applications. Rubicon models will require CV drive shaft w flange adapter (not avail from Pro Comp).
• (3) Vehicles with Auto Trans will require removal of front skid plate when using transfer case lowering hardware.
• (4) All ride height increases are approximate and will vary due to vehicle specification (Engine size, factory options, trail equipment, etc).
• (5) Coil spacer 55496 can be used to increase front ride height by .75".
• (7) Vehicle will require alignment after kit is installed.
• (8) Front cambolt kit 20-65226 is recommended for caster angle adjustments. In most cases, reducing positive caster to the minimum factory specification will reduce or eliminate the potential for steering wheel shimmy.
• (9) Rear cambolt kit 20-65225 can be used for tuning pinion angle for minor driveline vibration correction.

Features:

• Shocks: Front/Rear ES3000
• Max Tire Size: 32x11.50R15-20, 265/75R16, 265/70R17, 285/60R18, 275/55R20
• Wheel Size: 15" thru 20" up to 9" wide rims with 3.5" to 4.5" BS
• Front Lift: Coil Springs
• Rear Lift: Coil Springs
• Install Time: 2-4 Hours

Notes:

• (2) Driveline modifications may be required for height increases over 1.5" due to increased driveline angles. Transfer case SYE (Slip Yoke Eliminator) kit and CV rear drive shaft required for Long Arm Applications. Rubicon models will require CV drive shaft w flange adapter (not avail from Pro Comp).
• (3) Vehicles with Auto Trans will require removal of front skid plate when using transfer case lowering hardware.
• (4) All ride height increases are approximate and will vary due to vehicle specification (Engine size, factory options, trail equipment, etc).
• (5) Coil spacer 55496 can be used to increase front ride height by .75".
• (7) Vehicle will require alignment after kit is installed.
• (8) Front cambolt kit 20-65226 is recommended for caster angle adjustments. In most cases, reducing positive caster to the minimum factory specification will reduce or eliminate the potential for steering wheel shimmy.
• (9) Rear cambolt kit 20-65225 can be used for tuning pinion angle for minor driveline vibration correction.

Features:

• Shocks: Front/Rear ES3000
• Max Tire Size: 32x11.50R15-20, 265/75R16, 265/70R17, 285/60R18, 275/55R20
• Wheel Size: 15" thru 20" up to 9" wide rims with 3.5" to 4.5" BS
• Front Lift: Coil Springs
• Rear Lift: Coil Springs
• Install Time: 2-4 Hours

Notes:

• (2) Driveline modifications may be required for height increases over 1.5" due to increased driveline angles. Transfer case SYE (Slip Yoke Eliminator) kit and CV rear drive shaft required for Long Arm Applications. Rubicon models will require CV drive shaft w flange adapter (not avail from Pro Comp).
• (3) Vehicles with Auto Trans will require removal of front skid plate when using transfer case lowering hardware.
• (4) All ride height increases are approximate and will vary due to vehicle specification (Engine size, factory options, trail equipment, etc).
• (5) Coil spacer 55496 can be used to increase front ride height by .75".
• (7) Vehicle will require alignment after kit is installed.
• (8) Front cambolt kit 20-65226 is recommended for caster angle adjustments. In most cases, reducing positive caster to the minimum factory specification will reduce or eliminate the potential for steering wheel shimmy.
• (9) Rear cambolt kit 20-65225 can be used for tuning pinion angle for minor driveline vibration correction.

Features:

• Shocks: Front/Rear ES9000
• Max Tire Size: 35x12.50R15-20, 35x12.50R15/ 315/75R16/315/70R17,305/70R18, 325/60R18, 295/60R20
• Wheel Size: 15" thru 20" up to 9" wide rims with 3.5" to 4.5" BS
• Front Lift: Coil Springs
• Rear Lift: Coil Springs
• Install Time: 10-12 Hours

Notes:

• (1) Use of a 35" x 12.50" tires will require wider replacement fender flares or steel flat fenders.
• (2) Driveline modifications may be required for height increases over 1.5" due to increased driveline angles. Transfer case SYE (Slip Yoke Eliminator) kit and CV rear drive shaft required for Long Arm Applications. Rubicon models will require CV drive shaft w flange adapter (not avail from Pro Comp).
• (4) All ride height increases are approximate and will vary due to vehicle specification (Engine size, factory options, trail equipment, etc).
• (5) Coil spacer 55496 can be used to increase front ride height by .75".
• (7) Vehicle will require alignment after kit is installed.

Features:

• Shocks: Front/Rear ES9000
• Max Tire Size: 35x12.50R15-20, 35x12.50R15/ 315/75R16/315/70R17,305/70R18, 325/60R18, 295/60R20
• Wheel Size: 15" thru 20" up to 9" wide rims with 3.5" to 4.5" BS
• Front Lift: Coil Springs
• Rear Lift: Coil Springs
• Install Time: 10-12 Hours

Notes:

• (1) Use of a 35" x 12.50" tires will require wider replacement fender flares or steel flat fenders.
• (2) Driveline modifications may be required for height increases over 1.5" due to increased driveline angles. Transfer case SYE (Slip Yoke Eliminator) kit and CV rear drive shaft required for Long Arm Applications. Rubicon models will require CV drive shaft w flange adapter (not avail from Pro Comp).
• (4) All ride height increases are approximate and will vary due to vehicle specification (Engine size, factory options, trail equipment, etc).
• (5) Coil spacer 55496 can be used to increase front ride height by .75".
• (7) Vehicle will require alignment after kit is installed.

Features:

• Shocks: Front/Rear ES3000
• Max Tire Size: 33x12.50R15-20, 285/75R-16, 285/70R17,295/65R18, 295/55R20
• Wheel Size: 15" thru 20" up to 9" wide rims with 3.5" to 4.5" BS
• Front Lift: Coil Springs
• Rear Lift: Coil Springs
• Install Time: 6-8 Hours

Notes:

• (2) Driveline modifications may be required for height increases over 1.5" due to increased driveline angles. Transfer case SYE (Slip Yoke Eliminator) kit and CV rear drive shaft required for Long Arm Applications. Rubicon models will require CV drive shaft w flange adapter (not avail from Pro Comp).
• (3) Vehicles with Auto Trans will require removal of front skid plate when using transfer case lowering hardware.
• (4) All ride height increases are approximate and will vary due to vehicle specification (Engine size, factory options, trail equipment, etc).
• (5) Coil spacer 55496 can be used to increase front ride height by .75".
• (7) Vehicle will require alignment after kit is installed.
• (8) Front cambolt kit 20-65226 is recommended for caster angle adjustments. In most cases, reducing positive caster to the minimum factory specification will reduce or eliminate the potential for steering wheel shimmy.
• (9) Rear cambolt kit 20-65225 can be used for tuning pinion angle for minor driveline vibration correction.

Features:

• Shocks: Front/Rear ES3000
• Max Tire Size: 33x12.50R15-20, 285/75R-16, 285/70R17,295/65R18, 295/55R20
• Wheel Size: 15" thru 20" up to 9" wide rims with 3.5" to 4.5" BS
• Front Lift: Coil Springs
• Rear Lift: Coil Springs
• Install Time: 6-8 Hours

Notes:

• (2) Driveline modifications may be required for height increases over 1.5" due to increased driveline angles. Transfer case SYE (Slip Yoke Eliminator) kit and CV rear drive shaft required for Long Arm Applications. Rubicon models will require CV drive shaft w flange adapter (not avail from Pro Comp).
• (3) Vehicles with Auto Trans will require removal of front skid plate when using transfer case lowering hardware.
• (4) All ride height increases are approximate and will vary due to vehicle specification (Engine size, factory options, trail equipment, etc).
• (5) Coil spacer 55496 can be used to increase front ride height by .75".
• (7) Vehicle will require alignment after kit is installed.
• (8) Front cambolt kit 20-65226 is recommended for caster angle adjustments. In most cases, reducing positive caster to the minimum factory specification will reduce or eliminate the potential for steering wheel shimmy.
• (9) Rear cambolt kit 20-65225 can be used for tuning pinion angle for minor driveline vibration correction.

Features:

• Shocks: Front/Rear ES3000
• Max Tire Size: 33x12.50R15-20, 285/75R-16, 285/70R17,295/65R18, 295/55R20
• Wheel Size: 15" thru 20" up to 9" wide rims with 3.5" to 4.5" BS
• Front Lift: Coil Springs
• Rear Lift: Coil Springs
• Install Time: 6-8 Hours

Notes:

• (2) Driveline modifications may be required for height increases over 1.5" due to increased driveline angles. Transfer case SYE (Slip Yoke Eliminator) kit and CV rear drive shaft required for Long Arm Applications. Rubicon models will require CV drive shaft w flange adapter (not avail from Pro Comp).
• (3) Vehicles with Auto Trans will require removal of front skid plate when using transfer case lowering hardware.
• (4) All ride height increases are approximate and will vary due to vehicle specification (Engine size, factory options, trail equipment, etc).
• (5) Coil spacer 55496 can be used to increase front ride height by .75".
• (7) Vehicle will require alignment after kit is installed.
• (8) Front cambolt kit 20-65226 is recommended for caster angle adjustments. In most cases, reducing positive caster to the minimum factory specification will reduce or eliminate the potential for steering wheel shimmy.
• (9) Rear cambolt kit 20-65225 can be used for tuning pinion angle for minor driveline vibration correction.

Features:

• Shocks: Front/Rear ES3000
• Max Tire Size: 33x12.50R15-20, 285/75R-16, 285/70R17,295/65R18, 295/55R20
• Wheel Size: 15" thru 20" up to 9" wide rims with 3.5" to 4.5" BS
• Front Lift: Coil Springs
• Rear Lift: Coil Springs
• Install Time: 6-8 Hours

Notes:

• (2) Driveline modifications may be required for height increases over 1.5" due to increased driveline angles. Transfer case SYE (Slip Yoke Eliminator) kit and CV rear drive shaft required for Long Arm Applications. Rubicon models will require CV drive shaft w flange adapter (not avail from Pro Comp).
• (3) Vehicles with Auto Trans will require removal of front skid plate when using transfer case lowering hardware.
• (4) All ride height increases are approximate and will vary due to vehicle specification (Engine size, factory options, trail equipment, etc).
• (5) Coil spacer 55496 can be used to increase front ride height by .75".
• (7) Vehicle will require alignment after kit is installed.
• (8) Front cambolt kit 20-65226 is recommended for caster angle adjustments. In most cases, reducing positive caster to the minimum factory specification will reduce or eliminate the potential for steering wheel shimmy.
• (9) Rear cambolt kit 20-65225 can be used for tuning pinion angle for minor driveline vibration correction.